VMO's stuff (LMP1 Released!).

[vmo]

If anyone downloaded my non GT-r R35 body in workshop, and put a fixture in the rear part (like ohm1996 noticed), the fixtures are "absorbed" by the body.

Is the UV mapping done properly? Or the materials? The UV mapping for the rear should cover materials 9 (rear panel material) and 12 (rear seam material).

I mapped like the tutorial (with plane).

[strop]

It looks good so far. Aside from that known issue, the other problem is that with the material on the bottom of the car, it's impossible to place fixtures there where a lip would normally go!

[vmo]

It looks good so far. Aside from that known issue, the other problem is that with the material on the bottom of the car, it's impossible to place fixtures there where a lip would normally go!

True! I need to change only the ecs_plastic to ecs_body

[vmo]

I'm making the Huracan, but this time I used other method (not making the seams to make a more accurate shape, and make this at the finish), but I don't know how can I make the seams now, because the cut tool is a little bugged (sometimes can't cut a straight line between 2 parallel lines, cut in 5 points).

Anyone knows how can I make the seams?

Thanks.

hur.png (235.53 KiB) Viewed 4805 times

P.S. I'm solving the GT-R bugs.

[vmo]

About the GTR: I tried to re-skin, but the rear fixtures had the same problem: are absorbed by the godzilla.

[maffc]

I'm making the Huracan, but this time I used other method (not making the seams to make a more accurate shape, and make this at the finish), but I don't know how can I make the seams now, because the cut tool is a little bugged (sometimes can't cut a straight line between 2 parallel lines, cut in 5 points).

Anyone knows how can I make the seams?

Thanks.

P.S. I'm solving the GT-R bugs.

Yeah the cut tool is a little bugged, it works best if your view is not square on, also the projected lines do not necessarily match the end result.
What I tend to do is ignore the preview and just cut, often it does what I wanted. If it didn't then I just undo and try smaller cuts.
Also, what you could do is move the already existing edges (making sure they confirm to surface) to where you want the breaks, select all the polys that make up the door, etc and detach as element.

[vmo]

I'm making the Huracan, but this time I used other method (not making the seams to make a more accurate shape, and make this at the finish), but I don't know how can I make the seams now, because the cut tool is a little bugged (sometimes can't cut a straight line between 2 parallel lines, cut in 5 points).

Anyone knows how can I make the seams?

Thanks.

P.S. I'm solving the GT-R bugs.

Yeah the cut tool is a little bugged, it works best if your view is not square on, also the projected lines do not necessarily match the end result.
What I tend to do is ignore the preview and just cut, often it does what I wanted. If it didn't then I just undo and try smaller cuts.
Also, what you could do is move the already existing edges (making sure they confirm to surface) to where you want the breaks, select all the polys that make up the door, etc and detach as element.

Thanks!

[vmo]

In 3ds max, I'm making a tailight, but the bones doesn't move the headlight.

I tried 6 times, and anything.

Here is the file:

tailight.zip

(116.59 KiB) Downloaded 194 times

I weighted the bones.

[thecarlover]

The trick for the seams is the inset tool (the menu one that lets you enter exact values) being used twice. Select all the polys you want used for a door, hood, etc, and inset them twice, which will give you 2 rows of thin polys. Then grab the line in the middle and move it into the body as far as you want. To then make it its own element, select all the polys that will be part of that door (including the inner side of the seam), copy the position of one of the axises (like -85.3 cm on X), and then clone that selection along that axis. After that, delete the area you cloned from the model, then select the door you just cloned that's separated and paste the position value of the axis and the door will then be placed exactly where it was before but as its own element.

[Sillyworld]

Oh, that's how you do the seams? I select the polys for the door/bonet/trunk, and de-atach them to a different object. Then I select the edges, drag-copy them down or to the interior side, for both the door and the car body. Adjust the vvertices so the seams can be seen, and then I re-atach them together.

[maffc]

Each to their own I guess, either way seems valid. You probably couldn't tell which way was used in the end.

[vmo]

I solved the huracán issue.

Only i had problems with the taillighr.

[Oskiinus]

Anyone said Huracan?

[vmo]

Anyone said Huracan?

mmm.... Nope.

[Speedemon]

Anyone said Huracan?

Yea. You did.